Adding my ISP's data to Orion
My ISP has "real time" traffic graphs that require a log in. Is there a way to add these graphs as a window for my NOC?
View ArticleAre you KIDDING ME.....!!!
Is there any way to create an alert for a group that I have created in NCM? I pulling my hair out on how to do this. I have tried both the Basic and Advanced Alert Manager. Even had a Solarwinds S-Rep...
View ArticleClik here to view.
"Missing" nodes and NCM 7.3 Upgrade Issues
Last week, I upgraded my entire Orion installation (both my primary and additional pollers) to all the latest versions. Since then, I have been having issues with NCM. The first issue is that now...
View ArticleMonitoring Palo Alto 5060s
I found this thread: Support for Palo Altos Which doesn't seem to be answered. Is there anything further on this topic? I'm hoping to get more information to build good reporting on the devices.
View ArticleRecommend NCM on Spread the Word for a $25 Amazon gift card!
Let the community know how impressed you are with NCM and earn a $25 Amazon gift card! Simply post your review in Spread The Word with the questions answered below: What was life like before...
View ArticleNeed help with scripting- identify device-push config
I am new to the Orion product and I need to write a script which I can do. But is it possible to do what I have listed below. Script 1: Need to identify all 2900 series “Data” routers and then push a...
View ArticleNCM Config change template reserverd word syntax - @
We are trying to script a FTP server that uses authentication. The FTP syntax username:password@ftpserver. How does one pass the restricted @ symbol in NCM through to the FTP server? Usually there...
View ArticleThere was no endpoint listening
Can anyone help with the below message. Server has been running for 2 years, got rebooted and now it doesn't work. I opened a case with SW but I am getting replies outside my timezone so it's on...
View Article0x80040217 The server response was not available
Hi all, I am trying to send the results from a scheduled NCM job to an email address. The SMTP server settings and authentication is right, firewall is shut down and the recipient is from the same...
View ArticleGet config from Cisco switches with SNMP/TFTP
Hello all,I am new to NCM, and I have one question for which I can't seem to find answer in documentation. Can anyone explain me configuration retrieval process when SNMP/TFTP is used. I was under...
View ArticleMake Config Change Reports Smaller
I currently have 64 nodes and if we do changes across our company to the switches and firewalls I get a 50 to 70MB email that shows the entire configs and changes. Is there a way to have it just show...
View ArticleNCM Config Change ASA Active/Standby
Hi All I am looking for a little help. Is it possible to have a config change script that logs into an ASA checks to see if it is the Active Unit then runs aseries of commands. Clearly i have got the...
View ArticleWhere can I get a device template for a Cisco ASA 5520 that will give me a...
I am backing up a Cisco ASA 5520 which is acting as a VPN firewall, problem is the config NCM is downloading for me is not enough. A "show run" command does not display enough information for me such...
View ArticlePolicy Question for Juniper JUNOS devices (Operational mode)
There are certain checks we'd like to make against our Juniper gear that only work in Operational mode. For non-juniper people, that means the information is not stored in the configuration. For...
View ArticleLicensing and node removal for NCM
We have a 200 node license available to us under NCM, but upon network discovery, 322 nodes were found. Many of these nodes we do not wish to manage under NCM. Is the license model designed in such a...
View ArticleNCM Config change template reserverd word syntax - @
We are trying to script a FTP server that uses authentication. The FTP syntax username:password@ftpserver. How does one pass the restricted @ symbol in NCM through to the FTP server? Usually there...
View ArticleNeed help with scripting- identify device-push config
I am new to the Orion product and I need to write a script which I can do. But is it possible to do what I have listed below. Script 1: Need to identify all 2900 series “Data” routers and then push a...
View ArticleInvoke Cirrus.Settings DecryptData via SWIS v3 over HTTPS
Hi - I am trying to Invoke a SWIS Verb via HTTPS using the following curl command: curl -k -u <user>:<pass> -X POST -H "Content-Type: application/json" -d '["ABC"]'...
View ArticleGet config from Cisco switches with SNMP/TFTP
Hello all,I am new to NCM, and I have one question for which I can't seem to find answer in documentation. Can anyone explain me configuration retrieval process when SNMP/TFTP is used. I was under...
View Article0x80040217 The server response was not available
Hi all, I am trying to send the results from a scheduled NCM job to an email address. The SMTP server settings and authentication is right, firewall is shut down and the recipient is from the same...
View Article